4 Simple Furnace Repair Tips

Experienced HVAC repair technicians perform furnace repair and maintenance services. They have years of experience repairing high-end furnaces, including both wood-and hybrid models. Whether you’re having trouble with your boiler or other heating device, it’s best to contact an experienced technician. They will be able to diagnose the issue, offer the most effective solution, and fix your furnace in less time than it would take you to replace it. With trained furnace repair professionals by your side, you can feel confident that they will do their best to make your heating unit run as efficiently as possible.

furnace repair professionals

There are several things to look out for when trying to repair your heating system. Here are the simple tips for furnace repair:

1. Proper Certifications

One of the first steps is making sure the technician has the proper certifications. In order to qualify, he must fulfill HVAC National Board Certified Qualifying Board (HVAC NSB) qualifications. As part of being certified, he must also complete a comprehensive heat installation training program and pass the state exam. When checking out prospective technicians, make sure to ask what certifications they hold and how long they’ve been doing this type of work.

2. The Right Equipment

Next, it’s important to check out the technician’s equipment. Since many HVAC services perform work using heaters, it’s important to find out what kind of equipment they’re using. Ask to see their gas tank to see if the gas is topped off. If so, it’s a good idea to wait a few hours while the technician tops off the gas. Leaving the gas in for too long can cause serious problems like leaks and possibly explosions. If you notice signs of wear or damage on the heating equipment, contact the gas company immediately.

If the furnace repair is running but not producing enough heat, there are several steps you can take to troubleshoot the issue. First, turn the power to the furnace on and check to make sure it’s actually functioning. If it’s not, then the next step is to open the furnace door safety switch. This is located directly above the furnace itself. You’ll need to unscrew the two screws that are holding it in place and pull the safety switch straight down. It’s important to note that this step doesn’t require any tools and will allow you to safely open the door.

3. Check the Filters

Next, if you find that the furnace filters are clogged, these are the repairs you’ll need to do. Remove the filter from the furnace and wipe it clean with a damp cloth. If it appears to be damaged or dirty, you may need to purchase new filters. If not, simply replace the ones you’ve removed and wipe the rest of them clean with another cloth.

4. Cool off the Blower

For the last step in furnace blower repairs, you’ll need to remove the blower and place it in an open space to allow it to cool off completely. This step is particularly important if your heating system hasn’t been running for a while and you’re afraid of overheating it again. Once the blower has cooled down completely, it can be removed from the system. Again, you’ll need to perform all of these steps one at a time in order to ensure you don’t skip any of the necessary parts.

5. Tackling Gas Leaks

One more furnace repair tip involves cleaning and repairing gas leaks and defective heat exchangers. These are especially common in older heat and air-conditioning equipment, often resulting from poorly maintained duct work and outdated insulation. Blocked ducts allow cold air to freely enter the furnace room, which then warms up the interior of the room. Warm air can create a drafty environment inside the house, causing expensive energy bills to go through the roof.

Blocked ducts are also known to cause hot spots, especially in areas where there’s not enough duct work in the house. These hot spots will typically show up as small bluish-green stains in ceilings, walls, doors, and windows.

To fix hot spots and prevent drafty drafts, you can perform a filter change on your furnaces. It’s important to note that filters should only be changed with a qualified technician, as filters can be dangerous if changed by an untrained consumer. Filters should be replaced every three to six months, depending on the size of the filter, but they should always be replaced before they become blocked with dust or grime. Furnace repair professionals can perform the proper filter change for your furnaces and can guarantee that the process is done right.

About Salman Zafar

Salman Zafar is the CEO of BioEnergy Consult, and an international consultant, advisor and trainer with expertise in waste management, biomass energy, waste-to-energy, environment protection and resource conservation. His geographical areas of focus include Asia, Africa and the Middle East. Salman has successfully accomplished a wide range of projects in the areas of biogas technology, biomass energy, waste-to-energy, recycling and waste management. Salman has participated in numerous national and international conferences all over the world. He is a prolific environmental journalist, and has authored more than 300 articles in reputed journals, magazines and websites. In addition, he is proactively engaged in creating mass awareness on renewable energy, waste management and environmental sustainability through his blogs and portals. Salman can be reached at salman@bioenergyconsult.com or salman@cleantechloops.com.
Tagged , , , , , , , , , , , , . Bookmark the permalink.

3 Responses to 4 Simple Furnace Repair Tips

  1. Pingback: The Function of Central Heating Radiators | BioEnergy Consult

  2. Pingback: The Complete Beginner's Guide to Furnaces

Share your Thoughts

This site uses Akismet to reduce spam. Learn how your comment data is processed.