A Guide On HVAC System Repair

HVAC maintenance and HVAC repair sometimes become necessary in certain situations. This is especially the case during hot summers. A malfunctioning unit can not only reduce comfort in the house, but also set the homeowner back large sums of money due to inefficiency.

hvac-repair

Heating Service Repair

Like with other domestic appliances, there are several things which could go wrong within a HVAC unit. Some of these problems occur more frequently than others. It’s possible to fix some issues without having to call an air conditioning expert.

If the house starts becoming unbearably hot, the first thing to check would be the thermostats. Older units can be accidentally switched from cool to off, especially when bumped into. Their digital counterparts are also affected when the battery starts losing power.

If lowering the thermostat fails to make the unit turn on, it could be due to a blown fuse or a tripped breaker. If this is reset or the fuse replaced and the problem still persists, it’s advisable to contact an electrician. Outdoor units that run constantly also tend to freeze up. This can be rectified by turning the unit off for some hours to let it thaw.

DIY AC Repair

Not many homeowners can undertake such a task on their own. This is because the expertise and equipment involved are usually advanced, which brings in the need for a trained specialist. Nevertheless, there are several things that one could check on their own to enhance the performance of their unit.

If the compressor fails to turn on, the breaker and fuse would be the components to check. A running unit that isn’t cooling could be due to low refrigerant level. This would require professional help to replenish. The condenser coils on both sides should also be checked to see if they’re dry. If this is the case, one would need to brush and vacuum them. One can do this at least twice each summer.

Hiring Expert HVAC Technicians

At best, the things that a typical homeowner can do on their own are limited. Typically, an issue will be too complex for even well-acquainted individuals to handle. Once it’s established that the hitch is outside an individual’s scope, there are several things one needs to consider before hiring an expert.

Ideally, a HVAC unit should be repaired before the summer season starts. This is because technicians get quite busy as the hot season progresses. This high demand makes it hard to schedule an appointment.

It would thus be prudent to call a furnace contractor in Brownsburg Indiana before the season starts. Typically, one is likely to land a convenient appointment time, and could even save some money. One will also be prepared for high temperatures that could occur later on in the season.

The Features Of Best Cordless Finish Nailer

A finish nailer is a powerful tool that is specifically made for both experienced and DIY home users. The finish nailer uses relatively smaller nails than other cordless nail guns but is designed to handle different jobs. A finish nailer is the best bet for installing trim, crown moulding or even suitable for specific cabinets and furniture finishing.

cordless-finish-nailer-DIY

What is the best cordless finish nailer?

A ‘finish nailer’ broadly refers to one with a 16 gauge, which is a little thicker nail than the 18 gauge brads. There can be a bit of confusion due to the fact of the higher the number of gauges, the thinner the nail will be. This is due to the number of nails that you can fit per inch (for example, 16 gauge = 16 nails per inch and 18 gauge = 18 per inch). Therefore, you need the right nail for the proper work, so that the structural integrity of the material is not splinted or harmed.

Cordless finish nailers are made by different and various reputable brands such as Dewalt, Makita and Porter-Cable. However, before you search for the best Finish nailer, it is important that you have the best table saw for woodworking too! If you want to have woodworking materials that can do the job and last for a long time, make sure to go for those that would give you value for your money.

What is the greatest advantage of Cordless Finish Nailer?

A finish nailer is a versatile commodity which can also be used for various tasks such as moulding, decorating, roofing and many other jobs. This can also move the nails from thin wooden panels to dense concrete material and other various materials.

Difference between angled and straight finish nailer

Angled finishing nailers are made to be for narrow or tight spaces project. This type of finish nailer is durable to drive more substantial gauged nails. Straight finish nailers, on the other hand, are used within open spaces, and it was built with sharper nails.

Features Of Best Cordless Finish Nailer

A cordless finish nailer is a durable and versatile tool to perform a range of tasks ranging from the installation of trim to the assembly of cabinets and furnishings. It is a reasonably robust tool that is built to drive comparatively smaller nails. Here is a great article on home newtools best cordless finish nailer

Below are the key features of the best cordless finish nailer:

1. Size and Weight

To finish work is usually a multi-day, all-day task. Which means you must hold your finish nailer device in your hand for extended periods. A cordless model doesn’t have a wired cord or pneumatic hose that you need to bring and handle with you. That lowers the stress on your wrists. Although, if your finish nailer is bulky, this might have an irreversible effect on your hand. On some models, the battery can add considerable weight to the tool. The greater the battery size, the more it will weigh and the larger it will be.

A cordless finish nailer needs to get into tighter spaces and work at odd angles compared to other nailers, so size is essential. Angled versions reduce the tool’s total height and can make use in tight spaces more straightforward. Search for a smaller, cordless finish nailer with a lighter, state-of-the-art battery that weighs as little as possible to help you continue to work for longer without hand fatigue.

2. Trigger Operation

There are two primary forms of trigger: bump fire and subsequent action. Faster is a bump-fire. You keep the pressure on the trigger and press the piston in the nail where you want to drive. This is quicker, so losing track of it is easier, and there is a higher chance of accidental shooting. A sequential operation allows you to release the trigger between the nails and press it in again before the next nail is pushed. It’s slower, but it’s a little safer and controllable.

Needless to choose either one or the other. There are many models on the market which accommodate both. And, if you’re not sure which one you want, or if there are moments when you’re going to need one, look for one that has both in features. These combination finish nailers either have some internal mechanism allowing you to switch between operating modes, or they enable you to switch triggers out. Others that will enable you to change triggers also don’t come along with the extra trigger. You’ll have to buy an extra one.

3. Quality

Although, many people believe in brand reputable when choosing tool quality. This is because a reputable company always protect their name and to do this, they keep on producing a quality product.

While there is no foolproof way to upfront predict tool quality, but reading feedback and trusting a well-known organization minimizes the risks of getting poor tool.

4. User friendly

We strongly recommend that you read reviews and check product details to find a model that will comfortable in your hands, given the simple cost of a finish nailer. This is a method that is expected to deliver reliable results depending on how you treat it. The standard of the job starts with your hand. It is believed anybody will want to choose a  non-cumbersome finish nailer.

best-cordless-nailer

5. Lighting

With LED light features, a finish nailer makes its way within dark spaces such as cabinets or low-light areas, like baseboards. A cordless model with LED lights will directly transmit shadowless light to the surface, so you will see what you are doing without external lighting.

6. Higher Nail Capacity

This is one of the essential features a best cordless finish nailer you have. Having higher nail capacity will assist you in concentrating on the work through the elimination of frequently nail refilled. Another benefit of higher nail capacity is that it saves time.

7. Nail Depth

Precision hitting is outstanding as firing is. Finishing nailer is expected to hit the appropriate depth of the nail. Many finishing nailers come with an adjustable depth sensor that helps you to set precision depth. So, when choosing your finishing nail to ensure it offers consistent nail depth across a variety of types of materials.

8. Jam Clearing

Tool-free jam clearing is one a great feature expected to look for in a finish nailer. Nail jam may occur at a time, and if your nailer does not possess smooth jam-free. There may be some difficulties in hunting down the nailer.

Although, jamming can be held to a minimum by keeping your nailer in place and making sure you use the right nails.

9. Warranty

An extended warranty is an indication that the manufacturer has faith in its materials and manufacturing. Search for the longest available warranty and a money-back guarantee just in case you are not satisfied with tools.

Final Word and Recommendation

Finish Nailer is commonly regarded as a technical tool, but this innovative tool has significantly changed the finishing game. This is the reason almost everybody or hobbyists are now using the device to execute their various projects. A cordless finish nailer is a versatile woodworker tool that helps to punch the nails seamlessly, and gives the woodworks a clean and finished look.

Cordless finish nailers are fantastic, and there are plenty of models available which you can select the right cordless finish nailer to suit your work needs.

6 Plastic-Free Bathroom Swaps You Should Start Making

Plastic pollution is a global concern that’s significantly affecting the state of the environment. It can threaten the wildlife present in various areas and affect the health and safety of the human population. However, it’s also undeniable that some industries continue to produce and use plastic for their products.

If you wish to minimize your plastic waste and help preserve the environment, you can make some sustainable swaps in your daily lifestyle. To start, you can try going for these choices to make your bathroom plastic-free:

1. Use Natural Soap Made With Sustainable Ingredients

Nowadays, some hygiene products like soap or shampoo often come in plastic packaging that aren’t biodegradable. If you aren’t mindful of the types of items you buy, you may not notice how much waste you accumulate whenever you get self-care products from your local store. So if you wish to modify certain aspects of your hygiene routine in order to help the environment, use natural soap made with sustainable ingredients and packaging.

There are earth-friendly brands promoting various goods that produce little to no waste and are contain all-natural ingredients. Using their products may benefit not just the planet but also your body.

soap made with natural ingredients

For example, Earthbits have a great range of natural soap made with gentle components. They offer options that don’t have any chemicals and are just as effective as those sold by commercial soap brands. Sustainable soaps can clean your body well without exposing your skin to too many chemical ingredients. You can try to find the scent and formulation you want so you can transition to a new product more comfortably.

“Cedarwood and Lemongrass Natural Soap from EarthBits”

2. Try Bar Shampoo

Besides your soap, you can also get your hair care products in a solid form. Usually, shampoo products sold in shops are packaged in plastic bottles and come in a liquid formula. It can be challenging to find ways to repurpose those containers that accumulate in your home, especially if you have a busy lifestyle. Hence, finding an eco-friendlier alternative that’s compact and more practical may be a good choice for your bathroom needs.

Some bar shampoos look like regular soap but are formulated specifically for your hair. You can use them to wash your crowning glory in the same way you use liquid shampoo. But thanks to their solid and compact appearance, you can save space in your bathroom and also lessen the amount of product you use during each shower you take.

3. Switch To A Bamboo Toothbrush

One effective method you can do to reduce your plastic waste production is to switch from regular plastic toothbrushes to bamboo ones. Although there are recyclable plastic items out there, traditional toothbrushes aren’t one of them. The bristles and handle of the brush are made with different materials, so they can’t be recycled. In fact, about one billion toothbrushes used in the United States end up in the trash each year.

plastic-free bathroom

Hence, a simple switch from a plastic item to a bamboo-made one can significantly reduce the amount of waste you have to get rid of. Some sustainable products are made with charcoal-infused bristles that are biodegradable and detachable. Once the bristles are old and worn out, you can simply throw them into homemade compost.

There are places where you can buy bamboo toothbrushes in bundles to save some money. They’re also easy to find, so you won’t need to worry about where you should get your supply by the time you need to replace the one you’re using.

4. Opt For Recycled Toilet Paper

For some households, it’s almost impossible not to have a supply of toilet paper in the bathroom. It serves multiple purposes like cleaning surfaces or drying wet places. Although the materials used to make tissue are recyclable, it isn’t easy to find recycling centers that accept them. The fiber composition of used tissue paper can’t be used to create good-quality paper, so that item is usually rejected. They also often come in plastic packaging, which you simply throw away once you need to use the toilet paper.

sustainable bathroom swaps

Living without tissue may be difficult, so if you wish for a more sustainable solution, you can start using recycled toilet paper instead. Given the materials used to make it, using it may lessen the carbon footprint you leave on the environment. Using recycled toilet paper helps conserve water and trees as well since it’s made with repurposed materials. In some cases, the packaging used for it is also recycled, so you won’t need to worry about contributing to the plastic waste piling up in landfills.

5. Make Your Own Toothpaste

More often than not, toothpaste is packaged in plastic tubes to make it easier for anyone to control how much they use. Once the product has been consumed, the only destination for the tube is the trash bin. So if you want to avoid throwing away more plastic and save money on your oral hygiene products, try making toothpaste instead.

You can create your own oral cleaning product with common ingredients like baking soda, coconut oil, and peppermint. If you refrain from purchasing your toothpaste from the grocery store, you can effectively lessen the number of empty plastic tubes you have to get rid of several times a year.

6. Avoid Small Packaging

Some hygiene or skincare products come in small plastic packaging. For instance, sample sizes of serums or facial creams are placed in pocket-sized containers made of plastic. Those can accumulate over time and exacerbate the problem with plastic waste. Hence, you should either purchase your personal care items in large quantities or simply avoid using products in small plastic containers.

For example, if you’ve been using the same face moisturizer for a long time, purchase the biggest available size instead of getting the smaller ones every time. Also, it would help to be conscious about how you get rid of empty containers. Some brands encourage customers to return empty packaging so they can recycle it. If you’re conscious about the condition of the environment, patronize brands that also care for nature as much as you can.

sustainable bathroom

Final Thoughts

It can be challenging to eliminate or lessen your consumption of plastic products. Like your food supply and personal hygiene items, most of the goods you buy in stores are packed in plastic. So if you want to help Mother Nature, try to make sustainable swaps in your household, including your bathroom. You can purchase your soap and shampoo from eco-friendly brands that don’t use plastic packaging. Such simple changes may help preserve the environment, so don’t hesitate to give them a go.

Eco-Friendly Ways to Get Rid of Mold in Your Bathroom

Most homeowners have black mold in their homes without even knowing. Most types of mold grow in dark, warm, and humid places that are often hidden, such as bathrooms. With the right conditions, mold can grow within 48 hours, and leaving it untreated might lead to several health conditions, including respiratory illnesses and aggravated allergies, and asthma. Therefore, you should clean mold immediately and find ways of preventing recurrent growth.

Unfortunately, most conventional mold cleaning products are made from harmful ingredients. The Environmental Working Group found ingredients that irate the lungs in half of these products. However, you can avoid these harmful products and consider eco-friendly and overly effective cleaning products. These natural mold cleaning products include:

Eco-Friendly Ways to Get Rid of Bathroom Mold

1. Vinegar

White vinegar is a safe and affordable natural mold cleaning solution that clears mold growth in the bathroom and other surfaces expertly. The solution has antibacterial properties that make it effective in cleaning and preventing mold growth. Regular vinegar used for cooking contains 5% of acetic acid. However, you should use white vinegar with 6% to eliminate mold. The extra percentage is what makes it effective. You can find this in your local home improvement stores.

To use the solution, transfer undiluted vinegar into a spray bottle and spray it directly into the surface with mold. Let it sit for one hour, use a scrub brush to loosen any stubborn mold, and wipe the surface with warm water.

2. Hydrogen Peroxide

You can also clean your bathroom mold effectively using hydrogen peroxide. It is a three-in-one agent with antibacterial, antifungal, and antiviral properties that is safe to use and environmentally friendly. You can use the solution to kill mold from porous household materials, such as woven furniture.

To use hydrogen peroxide, mix two parts of water with one part of hydrogen peroxide solution in a spray bottle. If you don’t have a spray bottle, you can soak the solution in a towel and wipe the affected surface directly. Allow the solution to settle on the surface for 10 minutes, scrub it with a toothbrush, and wipe the remaining mold with a towel.

3. Tea Tree Oil Solution

Tea tree oil solution is not only effective in keeping spiders away but also a natural and safe option for getting rid of mold from your bathroom. This natural fungicide is a strong cleaning agent that can kill and prevent mold spores from growing. To make this solution, mix one teaspoon of tea tree oil with one cup of water and adjust the ratio of this mixture accordingly.

Shake the solutions to mix and apply using a spray bottle for better coverage. After applying to the area covered by mold, leave it for one hour to dry, then wipe the surface using a dry towel or microfiber clothing. Always use gloves or other protective gear since it can irritate your skin despite being a natural solution.

4. Grapefruit Seed Extract

The grapefruit seed extract is well known for its myriad health benefits. However, very few people know of its effective cleaning abilities. What makes this product very effective in cleaning mold in the bathroom and any other rooms in your home is the presence of polyphenols or limonoids and naringenin in the extract.

These compounds are effective in killing bacteria in carpet spills and laundry, which often promote mold growth. When used to fight bathroom mold growth, these acids penetrate any growth, preventing mold spores from recurring.

To use the solution;

  • Mix ten drops of grapefruit seed extract with one cup of water
  • Spray the solution and let it sit for between 10 minutes and one hour, depending on the saturation of mold, then wipe the residue
  • As with other natural remedies, use a spray bottle to saturate all the affected spots in your bathroom.

5. Lemon Juice

While this isn’t the strongest solution, lemon juice is widely available in most kitchens. Besides being natural, everybody likes the enticing smell of fresh lemon. That said, slice and juice five or more lemons depending on the size of the affected area. Pour the solution and leave it for five minutes, then wipe using a damp towel with warm water.

If the mold growth proves stubborn, you can scrub the bathroom floor, walls, or ceiling using a toothbrush. For optimal results, mix the lemon juice with hand or dish soap and some water.

Conclusion

The presence of mold in bathroom predisposes occupants to various health hazards, particularly respiratory problems. In severe cases, it can aggravate pneumonia, especially if someone had pre-existing health conditions. If you suspect mold growth in your bathroom, purchase a mold testing kit to confirm its presence. The above natural solutions can help in clearing small-scale mold growth. However, if the growth is extensive, hire mold remediation experts for professional services.

How Can You Produce Your Own Biogas?

The idea of biogas is anything but new. People have been experimenting with making biogas for many generations. Biogas is made by converting organic waste into energy. It’s a huge win for the environment because it utilizes what is otherwise considered waste, but it’s a big win for pocketbooks too.

Organic waste includes the byproducts of human food production (think potato peels, carrot peels, the tops of turnips, etc) but it also includes manure. Any manure is fair game, think about cows, pigs, chickens, rabbits, goats — virtually any farm animal produces mounds of this each day.

This manure produces very high levels of methane gas which is horrible for the environment. By using this manure to create biogas, we remove the danger of creating heat-trapping gases in our atmosphere that raises the temperature of the entire planet. Using it for biogas production can also help to reduce global warming.

How Do We Produce Biogas?

Biogas is produced from the breakdown of organic waste in an environment that is void of oxygen. We call this environment anaerobic and the process is process is called anaerobic digestion. Two products are created from this process. One is digestate. Digestate can be used for fertilizer and even as livestock bedding.  The other product is biogas. Biogas can be used for heating, electricity production and as a clean vehicle fuel.

It’s essentially like composting all of the materials, but in an environment without oxygen and in the temperature range of around 35 to 40 degrees Celsius and pH of around 7. This is optimal to produce biogas. Biogas can be converted into an upgraded form of gas by removal of carbon dioxide that can be used like natural gas. It can be used as-is as an engine fuel. It can be used as fuel in a vehicle, sometimes without modification.

How Can You Produce Your Own Biogas?

Just imagine being on your own off-grid property, running a hundred head of cattle, growing your own food and canning it. You’ve got meat covered, your food is stocked and you are prepared for just about anything. But what about fuel? Imagine what a game-changer it could be if you were able to produce your own fuel from the waste from your cattle and your garden scraps or food residuals! You can!

The Biogas Digester makes it possible, and fairly easy, for you to start producing your own biogas. Buy a ready-made biodigester for around $700-$1000 dollars and start producing your own biogas to meet your fuel requirements. They are containers designed to do the work for you and help you collect the fruits of your composted and digested waste.

Build your own! China has approximately 30 million Biodigesters in use in its rural areas. Rural Chinese areas are far removed from cities that have gas stations. It simply isn’t accessible as it is in the US. Many rural people have learned to make their own biodigesters to fill their fuel needs.

offgrid-biodigester

You need a tank that is sealed with an access hole on one side for adding organic waste. You have another access to an outlet. That is where you collect the liquid run-off that can be used for fuel.

The bottom of the main unit is the digestion chamber. From that is an outlet where the digestate can be collected and used as fertilizer. The main chamber typically has a domed top to allow for the room that will be necessary for the expansion of the gases formed inside. By being sealed, the unit creates that all-important anaerobic environment.

Useful Links

A tank that demonstrates the size and simplicity of a tank that can be purchased and used in the backyard.

https://www.etsy.com/listing/705458580/portable-home-biogas?gpla=1&gao=1&

This is a very in-depth article with directions for creating your own biodigester from Science Direct – https://www.sciencedirect.com/topics/engineering/biogas-digester

Easy DIY Projects to Reduce Your Carbon Footprint

Personal responsibility seems to be taking preeminence in every area of our lives. As time goes by, people are advised to change how they act in response to society’s change. The same case applies to reducing your carbon footprint. It’s time that everyone is held accountable for their contribution to climate change.

The constant reminder of our contribution to the carbon footprint is the first step to reducing your carbon footprint. Reducing carbon footprint will also save you time, money, energy, reduce pollution and enjoy a healthy environment. Of course, it is easier said than done, but everyone has to play a part to achieve this goal. Read this guide to learn all about carbon footprint.

What is Carbon Footprint?

Carbon footprint is the total amount of greenhouse gases, mainly methane and carbon dioxide, released directly into the atmosphere causing global warming.

How To Calculate Carbon Footprint

It is essential to calculate your carbon footprint to keep track of it and reduce it. There are calculators available online which will help you figure out your carbon footprint. Some of the standard data you will be asked about is:

  • The size of your home
  • Your diet
  • Mode of transport you use to run your daily business and for how long
  • The type of energy you use in your home

They may not be accurate enough since you’re using estimates, but they will give you a general idea about your carbon footprint and how to improve on it. So, here are the few DIY projects you can take to reduce your carbon footprint:

1. Recycle and Reuse to Reduce Waste

Your home is the first place where you can exercise recycling effectively to reduce your carbon footprint. If all of us can waste less and recycle more, this will be a massive step towards saving money and energy. Take note of the things that you use daily, which can be easily recycled. Some of these include:

  • Plastics
  • Paper
  • Glass
  • Aluminum

skip bins

You can also sell or donate some of the things you don’t need instead of wasting more of them in landfills. Other methods of recycling and reusing items in your home are:

  • Using old clothes as cleaning rags
  • Reusing your shopping bags instead of buying new ones
  • Buying recycled clothing
  • Reusing plastics

2. Use Energy Efficient Appliances

Even the smallest appliances can consume lots of energy. But don’t worry since there are simple but effective alternatives that you can use to reduce your home’s energy usage. These are:

  • Unplugging appliances that you’re not using like AC, charger, etc.
  • Switching off lights when you’re not using a room
  • Using LED light bulbs to save more energy
  • Using sustainable temperature control appliances like programmable thermostats and fans
  • Shift to solar energy

 

how to reduce energy bill

Try to use less energy in your home to reduce your carbon footprint. Talk to ac repair in Cherry Hill specialist to advise you on other innovative energy measures to take. They will also check your AC systems and do the necessary upgrades in your home to save more energy and reduce your utility bills.

3. Check on Your Water Usage

Water is one of the resources that you should safeguard at all costs. Most home systems receive water through pumping systems which consume a lot of energy. However, you can take simple DIY steps to save more water to prevent draining it into the environment. These include:

  • Harvesting water during the rainy season
  • Repairing faulty water leaks
  • Turning off the water when brushing or cleaning dishes
  • Reducing your bathing time

4. Use Alternative Transportation Methods

Are the errands that you need to run near your home? If so, consider using a bike or take a walk instead. By doing this, you will cut on the number of carbon emissions as you also keep healthy. Also, if you need to use a car, you can plan to complete all your errands in one day instead of several days.

green-travel

Also, if you have to use air travel, settle for the economy class other than first class. It is both cost-effective and has a lower carbon footprint on the environment.

5. Speak Up

One method of passing information is by speaking up. The more this information reaches the masses, the easier it will be to minimize carbon footprint. With the availability of the internet and social media, this is not too hard to achieve. You will be able to reach your family, friends, co-workers, etc. You can also participate in environmental volunteer programs to set an example for the rest. Words without action won’t have any impact.

Everyone has a personal responsibility to reduce their carbon footprint. All you need to do is follow the above tips to create a better and sustainable environment even for future generations.

What is Tire Recycling and How To Do It?

The old tires of your Subaru Forester are now worn out and no longer safe to be used on the road, says your mechanic. You’ve started shopping for new tires. But you wonder—what can you do with those old tires?

You can recycle it!

Tire recycling is the most practical and environment-friendly way of disposing of old and worn-out tires. Due to their inherent durability, large volume and environment and health risks, tires are one of the most problematic sources of solid wastes. Around the world, an estimated 2.5 million tires are thrown away yearly. With rubber recycling, tires can be given a new lease of life.

Benefits of tire recycling

Tire recycling can have numerous benefits not only for vehicle owners like you but also for the communities. For one, it can conserve landfill space. Because of their round and hollow shape, tires can take up significant space in landfills. Eliminating bulky items like tires can leave space in landfills for other things that cannot be easily recycled. There are many scientific papers about the benefits of processing, and if you were asked to write an essay, then you can contact this company with a request “buy essay” and a team of professional writers will help you

Tire recycling can also create new, beneficial products. Tire-derived fuel (TDF) is an example which is produced by subject scrap tires to high-temperature pyrolysis. This is reputed to be more energy-efficient than normal fuel. It also releases minimal emissions. Other useful products created from recycled tires are playground turf, railroad ties, and rubberized asphalt.

This process can also help in preventing the spread of diseases. Discarded old tires can provide a nesting place for rodents and mosquitoes. By recycling old tires, those pests can be eliminated. Consequently, diseases brought about by said animals can be prevented.

How to recycle tires

So, how do you recycle your old tires? One is to check with your local government about drop-off depots where you can bring your old tires for recycling. You may also bring those tires to household waste recycling centers.

These tires will then likely be packed and sent to processing plants, where they will be cut into smaller pieces by cut shredders. This is aimed at reducing the tire volume and creating a material that can be easily handled.

The end-product is a raw material that can be utilized for TDF, the most developed market for old tires in the United States. It is widely used in the country as a supplemental fuel by industries cement kilns, paper mills, and electric utilities, among others.

Tire shreds are then processed to remove the tire wire, which adds to the resilience, versatility, and strength of the tire. The wire is removed and recycled; often brought back to steel mills as these can be used in manufacturing new steel.

The remaining rubber is then screened to ensure that it is free from wires and other contamination. Afterward, the rubber is cleaned using water and other cleaning agents. Clean rubber is then packed and brought to other factories in need of rubber as raw material such as rubber shoe manufacturers.

Recycled rubber is also used in other ways such as ground rubber applications such as asphalt rubber, animal bedding, and synthetic sports field underlays. Asphalt rubber is widely used in Arizona, California, and Florida, for instance.

Other rubber by-products can be reused in various shapes and forms. For example, fiber and nylon make up nearly 15% of a tire. When extracted from old tires, these materials can be used in the manufacture of concrete, fiberglass, stucco, caret, and cleanup materials.

Rubber powder can also be derived from recycled tires. This high-performance but affordable material is used in creating sealing products, plastic, and rubber. It is a sustainable material with no adverse effects on

Other DIY ways to recycle tires

Yet DIY tire recycling can also come in other forms. You can reuse your old, worn-out tires in different ways.  One of the oldest ways to recycle old tires is to use them as tire swings. You can paint it first before hanging the tire on a tree. If you have many trees around your yard, you can hang a couple of old tires to create an entire swing set. This is an old-fashioned way to create a playset for your kids at home.

Tires can also be reused into tire climbers. Instead of spending several hundreds of dollars in a jungle gym, you can use old tires into a tire climber. Again, paint them first with bright colors. Bolt the tires together to make the tire climber safer for kids to play with.

You can also reuse old tires into a sandbox. This is particularly recommended if you have big tires like tractor tires. Put together several tractor tires in your yard and pain them. This is a nice way to thrill the kids during the summer.

An old tire can also serve as a hose caddy. Instead of leaving your garden hose and increasing its chances of getting damaged, you can secure it with a hose caddy made of an old tire. This is simple to do—cut the tire in half and coil the garden hose inside it. You may even paint the tire so that it would match your outdoor décor.

Finally, you can reuse tires into planters. There may be some cutting involved so prepare tools such as saw and hammer. Again, painting the tire may be optional. You can make several planters depending on the number of old tires you have.

There are other creative tire recycling ideas that you may explore such as turning old tires into chairs, welcome mats, dog bed, and see-saws.

Conclusion

As you can see, old tires don’t have to end up in the landfills. Tire recycling is the best and most ecologically-sound way of disposing of old tires.

There are many ways to recycle old tires. You can bring your old tires to a household waste recycling center where these are collected and segregated before being processed into various by-products.

You can also recycle tires through DIY projects. From tire planters to tire climbers, the possibilities are endless as far as recycling and reusing old and worn out tires are concerned.

Pros and Cons of Buying and Doing a DIY Solar Panel Installation

There’s a number of reasons why people invest in solar energy through solar panel installations on either their homes or other buildings. For some, they want their energy consumption to reduce their carbon footprint and make sure they live environmentally friendly. For others, they may want a power source they can use just in case the power were to shut off for a long period, or may want to earn tax incentives for going green.

But whichever reason you have, you have a choice between buying from a professional solar panel installation company, and going the DIY route. There are a few pros and cons to doing a DIY solar panel installation.

solar-energy-diy

Pro: You Can Determine Where And How You Want Your Solar Energy

If you have the time to design and build your own solar energy system, you can decide how you want it built and where you want it placed. One of the keys is buying solar panels for either on-grid or off-grid use, because that determines a lot in the scope of your installation.

But if you’re willing to take on the rigors of the installation, you’ll have the satisfaction of seeing solar power going to the areas of your property where you want.

Pro: There Is Some Savings You Can Get

Yes, getting DIY solar panels can save you some money, though it may not be as much as you want. The main area of savings is in the design and labor costs since you’re handling these yourself, but there can still be other costs you incur while taking the project on. For example, you may need storage or battery backups in some cases that may be a hidden cost. Still, you can usually save about a minimum of 10%-20% in overall costs by going DIY.

According to the experts at Unbound Solar, “Even if you extend your payback period by taking out a loan to finance your project, you still enjoy reduced electricity costs from the moment you flip the switch on your PV system.”

Con: Not All DIY Solar Panels Can Be Used On The Grid

While there are a few cases where you can install your own solar panels and remain connected to your utility provider, not all solar systems are designed for that. And some local governments have laws about what kind of solar panels and installations can be done that remain grid-tied. You’ll want to do research on whether you can do this before getting started.

Con: DIY Installation Can Be Quite Complex

While getting your own solar panel kit and building it yourself sounds easy enough, the process can be very intense and require a lot more know-how from the consumer than they might realize. Plus, there are tasks that need to be completed and signed off on by a certified electrician if your solar panels are going to be grid-tied, so you need to be aware of that. It’s usually going to require heavy duty tools and take some man power to get the system installed perfectly.

At the end of the day, installing your own solar panels can allow you to save a lot of money on energy, or get power to areas that it would be difficult to with a utility provider. But if you’re new to installing a solar panel system, you need to carefully consider the cost in both time and money to do it.