Author Archives: Salman Zafar

About Salman Zafar

Salman Zafar is the CEO of BioEnergy Consult, and an international consultant, advisor and trainer with expertise in waste management, biomass energy, waste-to-energy, environment protection and resource conservation. His geographical areas of focus include Asia, Africa and the Middle East. Salman has successfully accomplished a wide range of projects in the areas of biogas technology, biomass energy, waste-to-energy, recycling and waste management. Salman has participated in numerous national and international conferences all over the world. He is a prolific environmental journalist, and has authored more than 300 articles in reputed journals, magazines and websites. In addition, he is proactively engaged in creating mass awareness on renewable energy, waste management and environmental sustainability through his blogs and portals. Salman can be reached at salman@bioenergyconsult.com or salman@cleantechloops.com.

Sugarcane Trash as Biomass Resource

  By | | ,
15 Comments

Sugarcane trash (or cane trash) is an excellent biomass resource in sugar-producing countries worldwide. The amount of cane trash produced depends on the plant variety, age of the crop at harvest and soil and weather conditions. Typically it represents about 15% of the total above ground biomass at harvest which is equivalent to about 10-15 tons per hectare of dry matter. During the harvesting operation around 70-80% of the cane trash is left in the field with 20-30% taken to the mill together with the sugarcane stalks as extraneous matter.

cane-trash

Cane trash’s calorific value is similar to that of bagasse but has an advantage of having lower moisture content, and hence dries more quickly. Nowadays only a small quantity of this biomass is used as fuel, mixed with bagasse or by itself, at the sugar mill. The rest is burned in the vicinity of the dry cleaning installation, creating a pollution problem in sugar-producing nations.

Cane trash and bagasse are produced during the harvesting and milling process of sugarcane which normally lasts between 6 to 7 months. Cane trash can potentially be converted into heat and electrical energy. However, most of the trash is burned in the field due to its bulky nature and high cost incurred in collection and transportation.

Cane trash could be used as an off-season fuel for year-round power generation at sugar mills. There is also a high demand for biomass as a boiler fuel during the sugar-milling season. Sugarcane trash can also converted in biomass pellets and used in dedicated biomass power stations or co-fired with coal in power plants and cement kilns.

Burning of cane trash creates pollution in sugar-producing countries

Burning of cane trash creates pollution in sugar-producing countries

Currently, a significant percentage of energy used for boilers in sugarcane processing is provided by imported bunker oil. Overall, the economic, environmental, and social implications of utilizing cane trash in the final crop year as a substitute for bunker oil appears promising. It represents an opportunity for developing biomass energy use in the Sugarcane industry as well as for industries / communities in the vicinity.

Positive socio-economic impacts include the provision of large-scale rural employment and the minimization of oil imports. It can also develop the expertise necessary to create a reliable biomass supply for year-round power generation.

Recovery of Cane Trash

Recovery of cane trash implies a change from traditional harvesting methods; which normally consists of destroying the trash by setting huge areas of sugarcane fields ablaze prior to the harvest.  There are a number of major technical and economic issues that need to be overcome to utilize cane trash as a renewable energy resource. For example, its recovery from the field and transportation to the mill, are major issues.

Alternatives include the current situation where the cane is separated from the trash by the harvester and the two are transported to the mill separately, to the harvesting of the whole crop with separation of the cane and the trash carried out at the mill. Where the trash is collected from the field it maybe baled incurring a range of costs associated with bale handling, transportation and storage. Baling also leaves about 10-20% (1-2 tons per hectare) of the recoverable trash in the field.

A second alternative is for the cane trash to be shredded and collected separately from the cane during the harvesting process. The development of such a harvester-mounted cane trash shredder and collection system has been achieved but the economics of this approach require evaluation. A third alternative is to harvest the sugarcane crop completely which would require an adequate collection, transport and storage system in addition to a mill based cleaning plant to separate the cane from the trash .

A widespread method for cane trash recovery is to cut the cane, chop into pieces and then it is blown in two stages in the harvester to remove the trash. The amount of trash that goes along with the cane is a function of the cleaning efficiency of the harvester. The blowers are adjusted to get adequate cleaning with a bearable cane loss.

On the average 68 % of the trash is blown out of the harvester, and stays on the ground, and 32 % is taken to the mill together with the cane as extraneous matter. The technique used to recover the trash staying on the ground is baling. Several baling machines have been tested with small, large, round and square bales. Cane trash can be considered as a viable fuel supplementary to bagasse to permit year-round power generation in sugar mills.

Thus, recovery of cane trash in developing nations of Asia, Africa and Latin America implies a change from traditional harvesting methods, which normally consists of destroying the trash by setting huge areas of cane fields ablaze prior to the harvest. To recover the trash, a new so-called “green mechanical harvesting” scheme will have to be introduced. By recovering the trash in this manner, the production of local air pollutants, as well as greenhouse gases contributing to adverse climatic change, from the fires are avoided and cane trash could be used as a means of regional sustainable development.

Cane Trash Recovery in Cuba

The sugarcane harvesting system in Cuba is unique among cane-producing countries in two important respects. First, an estimated 70 % of the sugarcane crop is harvested by machine without prior burning, which is far higher than for any other country. The second unique feature of Cuban harvesting practice is the long-standing commercial use of “dry cleaning stations” to remove trash from the cane stalks before the stalks are transported to the crushing mills.

Cuba has over 900 cleaning stations to serve its 156 sugar mills. The cleaning stations are generally not adjacent to the mills, but are connected to mills by a low-cost cane delivery system – a dedicated rail network with more than 7000 km of track. The cleaning stations take in green machine-cut or manually cut cane. Trash is removed from the stalk and blown out into a storage area. The stalks travel along a conveyor to waiting rail cars. The predominant practice today is to incinerate the trash at the cleaning station to reduce the “waste” volume.

What Should You Look For in an Environmental Consulting Firm?

  By | | , ,
1 Comment

If you or your business has ever wanted to develop a property, chances are, you have probably worked with an environmental consulting firm, like Aegis Environmental, at some point in the process. If you haven’t yet, the chances are that you will. Environmental consulting is one of the most critical aspects of the planning process for any project. Unfortunately, it often doesn’t get the attention it deserves.

If you think you might be in need of environmental consultants for your project, keep reading to learn more about two of the most important services they can provide. Also, try to keep in mind that while these services may increase your initial costs up front, they save you time and money in the long run by ensuring things are done correctly from the start. This can also protect you from potential liabilities later on, should something go wrong on your property or with your project.

What Environmental Consultants Do

Environmental consultants offer many services that provide information necessary for any project, such as environmental impact assessments, ecological studies, and environmental and natural resource management systems. Some consultants, like the Sydney-based environmental consultants Molino Stewart, also offer stakeholder and community engagement and education services. These can be helpful in cases where developers, stakeholders, and the community may harbor different views of a project.

Most environmental consulting firms offer a very wide range of important services. However, some can have a larger impact on the success of your project than others. Not all consulting firms are made equal, but the really great ones share a few key hallmarks: a solid community and stakeholder engagement/education program, and a well-organized environmental and ecological impact assessment and management service.

Ecological Studies and EIAs

Before you can begin any construction or development project, you have to conduct ecological and environmental impact assessments (EIAs). These assessments map the flora and fauna of the ecosystems potentially affected by the project and quantify the biodiversity in these locations.

This information is required by various environmental protection acts to gain approvals for a project. The outcomes of these studies might also require management plans for vegetation and wildlife.

A good environmental consulting firm will have experts with all the proper certifications required to conduct every aspect of the study. They will also help you with the process of submitting the results and developing biodiversity management systems.  A great firm will even offer the planning and technology to implement those systems and help you through the entire approval process.

Stakeholder and Community Engagement

No matter the project or what it entails, chances are that someone, somewhere, will have an objection. Therefore, one key service you should look for in an environmental consulting firm is a good community education/outreach or a stockholder education program.

What does a good education program look like? Well, the first indicator is an adaptive education plan that can effectively target a broad range of demographics. This encompasses everything from local government councils and nearby residents to businesses and schools. This will help clear up any objections borne of misunderstandings. It will enable the community to more fully understand how your project will impact their environment and help them feel engaged in the process.

When it comes to stakeholder education and engagement, you want to look for a slightly different approach. These are people who will be directly impacted by the proposed project and hold a stake in its outcome. An effective education plan will provide subject background information that is relevant to all concerned parties. It will also include learning activities that cover the scope of the topic and clear guidelines that establish when and what is being done to address the issue.

Conclusion

You can’t overstate the importance of environmental consulting, so it is critical that you go with a good firm. It can be a little tricky to know which ones are best. Your best bet is to stick with ones that have a strong outreach and education program and a comprehensive impact assessment and management service.

Is Your Commercial Cleaning Service Sustainable?

  By | | , ,
4 Comments

It’s becoming more evident with time that people who want to ensure any form of financial security in the future need to start their own businesses. You can’t rely on your day to day job anymore to give you that feeling of financial security, and many are starting to realize this. So, people invest their money in all sorts of ventures, but one in particular has much potential for it if you know what you’re doing: commercial cleaning services. It’s probably crossed your mind at one point or another to start one, but there’s a problem stopping you. Is it sustainable? It can be, if you do all the right things.

A huge industry

In case you didn’t know it, the cleaning services industry is a multi-billion dollar one that is growing every year, and it’s a great business to get into if you know what you’re doing. The first thing you should do is identify if you want to get into home cleaning service or commercial cleaning service. The latter naturally takes the bigger chunk of the industry as a whole since companies hire atlanta cleaning service for regularly maintaining their office spaces.

Residential cleaning is also relevant to millions of people calling services to keep their houses clean, but it definitely isn’t as big as its commercial counterpart, and that’s why you probably started your cleaning service in the commercial sector. If you are aiming to make your business sustainable, you need to do a couple of things.

Stick to your niche

So, you started a commercial cleaning service, and there’s a lot of money in it. But that doesn’t mean you should get greedy and try to get into residential services as well. Spreading yourself too thin could be the end of your business, and you don’t really need to do it because the commercial cleaning industry is more than capable of sustaining your company.

Even if you hit a dry spell, don’t think about abandoning your specialty for the sake of another; instead, wait it out and things will get better for your company.

Cost VS quality balance

One of the most important things you need to do to keep Madison cleaning service running is maintaining a balance between keeping the cost low and yet giving your customers excellent quality.

You need to understand that there are dozens of others like you out there, so if your business sees a dip in quality, you’ll lose all your clients. Instead, you can cut costs by not having a large office space, for instance, or opting for older cleaning technologies, while still maintaining quality.

Invest in your people

For Wimbledon cleaning services, the most important asset is their personnel! All of the cleaning technicians are professionals who’ve gone through thorough training, allowing them to handle the great variety of cleaning solutions and to ensure the safety and satisfaction of the customers! They must always maintain professional conduct, so expect nothing but perfect results!

These are the most important points you need to tackle in order for your commercial cleaning service to be sustainable. If you can do that, the sky’s the limit for your business.

Why Wastewater Treatment is Crucial in Our Society

  By | | , , ,
1 Comment

Wastewater treatment is essential for maintaining proper balance throughout the world’s ecosystems. Wastewater contains toxic substances that harm wildlife and humans, including (and especially) aquatic life. This toxic water comes from a variety of sources, including sewage systems.

When organic matter enters a water source, like a river, aquatic lifeforms consume it as food. As the organic pollutants break down, the animals require more oxygen for the process. This leaves less oxygen in the water overall. When oxygen levels become dangerously low, animals in the water suffocate and die.

effluent-treatment-plant

Wastewater is toxic

Although some fish and other animals can break down toxins, toxic water is a serious risk to human health and is responsible for millions of deaths each year, mostly in developing nations.

Unclean water also causes diseases like cholera and schistosomiasis. Although these diseases generally occur in developing countries that don’t treat their wastewater, they can occur anywhere.

What is wastewater treatment? How does it work?

Wastewater treatment is the process of filtering contaminants out of water that has been previously used for another purpose. This process can occur both naturally and through manmade efforts.

Our ecosystem has a natural water treatment system that involves microorganisms that eat waste material, along with different layers of substrate and soil that filter the water as it absorbs into the earth. However, this process is too slow to efficiently filter the enormous amount of wastewater produced by humans. That’s where water treatment facilities come into play.

Water treatment plants are complex systems

What exactly happens at a wastewater treatment plant? While there are different methods, some of the systems use similar components. For example, the Four Rivers Sanitation Authority in Illinois treats wastewater by first pumping it to a higher elevation for gravity to pull the water through the first part of the treatment and filtering process.

The treatment process begins by filtering out the largest debris like plastic to prevent the pumps from becoming damaged. Debris that gets filtered out is then sent to a landfill.

Next, abrasive materials like sand and coffee grounds are filtered out of the wastewater. This grit is separated and sent to a landfill.

Settling tanks are then used to filter out fats, oils, and greases. These tanks also separate solids, most of which are sent to a separate processing facility. A small amount of solids are sent to the aeration tanks to maintain the proper environment required for microorganisms to devour the solids.

The water is then processed through a second set of settling tanks and is then disinfected with high-powered bleach. Sodium bisulfite is used to reduce the amount of chlorine in the water to make it less harmful to plant life when it’s discharged into the river.

What is in wastewater, exactly?

Since wastewater comes from human use, thousands of contaminants are present, although not all are present in every batch of water. In general, there are both inorganic and organic compounds found in wastewater.

sewage_sludge

Organic matter found in wastewater includes:

  • Proteins
  • Fats
  • Oils
  • Greases
  • Synthetic compounds from detergents
  • Carbohydrates

Inorganic matter found in wastewater includes:

  • Copper
  • Lead
  • Nickel
  • Magnesium
  • Potassium
  • Zinc
  • Sodium

Most of these contaminants come from industrial wastewater and aren’t easily broken down. When these inorganic compounds collect in water sources, they build up over time, making the water increasingly toxic to animals and humans.

Other matter found in wastewater includes:

  • Nutrients: High levels of nitrogen and phosphorous create “dead zones” by feeding large algae blooms. These blooms block sunlight, causing plants to die. Bacteria then proliferate by feeding on the dead plant matter.
  • Microorganisms: Harmful microorganisms include E. coli, parasites, and bacteria.
  • Pharmaceuticals: Pharmaceuticals enter wastewater through human waste and people flushing drugs down the toilet.

Wastewater treatment can help with water scarcity

There are many places across the world that experience droughts and water shortages on a regular basis. Without treating wastewater, drinking water sources become (and remain) contaminated. This includes rivers, lakes, and streams.

Treating wastewater in these areas would provide residents with a clean source of water to use for drinking, washing clothes, and bathing. After continually treating the wastewater, it would eventually bring the rivers, lakes, and streams back to a less-polluted state over a long period of time.

However, getting a treatment system set up takes money, time, and resources. The nations that need it the most can afford it the least. However, there are people and organizations working on solutions to this problem.

It’s not an overnight fix, but hopefully, one of those organizations will soon create a successful model that works for developing nations.

Collection Systems for Agricultural Biomass

  By | | , ,
10 Comments

Biomass collection involves gathering, packaging, and transporting biomass to a nearby site for temporary storage. The amount of biomass resource that can be collected at a given time depends on a variety of factors. In case of agricultural residues, these considerations include the type and sequence of collection operations, the efficiency of collection equipment, tillage and crop management practices, and environmental restrictions, such as the need to control soil erosion, maintain soil productivity, and maintain soil carbon levels.

biomass-collection-systems

The most conventional method for collecting biomass is baling which can be either round or square. Some of the important modern biomass collection operations have been discussed below:

Baling

Large square bales are made with tractor pulled balers. A bale accumulator is pulled behind the baler that collects the bales in group of 4 and leaves them on the field. At a later date when available, an automatic bale collector travels through the field and collects the bales.

The automatic bale collector travels to the side of the road and unloads the bales into a stack. If the automatic bale collector is not available bales may be collected using a flat bed truck and a front end bale loader. A loader is needed at the stack yard to unload the truck and stack the bales. The stack is trapped using a forklift and manual labor.

biomass-collection

Loafing

When biomass is dry, a loafer picks the biomass from windrow and makes large stacks. The roof of the stacker acts as a press pushing the material down to increase the density of the biomass. Once filled, loafer transports the biomass to storage area and unloads the stack. The top of the stack gets the dome shape of the stacker roof and thus easily sheds water.

Dry Chop

In this system a forage harvester picks up the dry biomass from windrow, chops it into smaller pieces (2.5 – 5.0 cm). The chopped biomass is blown into a forage wagon traveling along side of the forage harvester. Once filled, the forage wagon is pulled to the side of the farm and unloaded. A piler (inclined belt conveyor) is used to pile up the material in the form of a large cone.

Wet Chop

Here a forage harvester picks up the dry or wet biomass from the windrow. The chopped biomass is blown into a forage wagon that travels along side of the harvester. Once filled, the wagon is pulled to a silage pit where biomass is compacted to produce silage.

Whole Crop Harvest

The entire material (grain and biomass) is transferred to a central location where the crop is fractionated into grain and biomass.  The McLeod Harvester developed in Canada fractionates the harvested crop into straw and graff (graff is a mixture of grain and chaff). The straw is left on the field. Grain separation from chaff and other impurities take place in a stationary system at the farmyard.

McLeod Harvester fractionates the harvested crop into straw and graff

For the whole crop baling, the crop is cut and placed in a windrow for field drying. The entire crop is then baled and transported to the processing yard. The bales are unwrapped and fed through a stationary processor that performs all the functions of a normal combine. Subsequently, the straw is re-baled.

Properties and Uses of POME

  By | | ,
8 Comments

Palm Oil processing gives rise to highly polluting wastewater, known as Palm Oil Mill Effluent (POME), which is often discarded in disposal ponds, resulting in the leaching of contaminants that pollute the groundwater and soil, and in the release of methane gas into the atmosphere. POME is an oily wastewater generated by palm oil processing mills and consists of various suspended components. This liquid waste combined with the wastes from steriliser condensate and cooling water is called palm oil mill effluent.

POME

On average, for each ton of FFB (fresh fruit bunches) processed, a standard palm oil mill generate about 1 tonne of liquid waste with biochemical oxygen demand 27 kg, chemical oxygen demand 62 kg, suspended solids (SS) 35 kg and oil and grease 6 kg. POME has a very high BOD and COD, which is 100 times more than the municipal sewage.

POME is a non-toxic waste, as no chemical is added during the oil extraction process, but will pose environmental issues due to large oxygen depleting capability in aquatic system due to organic and nutrient contents. The high organic matter is due to the presence of different sugars such as arabinose, xylose, glucose, galactose and manose. The suspended solids in the POME are mainly oil-bearing cellulosic materials from the fruits. Since the POME is non-toxic as no chemical is added in the oil extraction process, it is a good source of nutrients for microorganisms.

Biogas Potential of POME

POME is always regarded as a highly polluting wastewater generated from palm oil mills. However, reutilization of POME to generate renewable energies in commercial scale has great potential. Anaerobic digestion is widely adopted in the industry as a primary treatment for POME. Biogas is produced in the process in the amount of 20 m3 per ton FFB. This effluent could be used for biogas production through anaerobic digestion. At many palm oil mills this process is already in place to meet water quality standards for industrial effluent. The gas, however, is flared off.

Palm oil mills, being one of the largest industries in Malaysia and Indonesia, effluents from these mills can be anaerobically converted into biogas which in turn can be used to generate power through CHP systems such as gas turbines or gas-fired engines. A cost effective way to recover biogas from POME is to replace the existing ponding/lagoon system with a closed digester system which can be achieved by installing floating plastic membranes on the open ponds.

As per conservative estimates, potential POME produced from all Palm Oil Mills in Indonesia and Malaysia is more than 50 million m3 each year which is equivalent to power generation capacity of more than 800 GW.

New Trends

Recovery of organic-based product is a new approach in managing POME which is aimed at getting by-products such as volatile fatty acid, biogas and poly-hydroxyalkanoates to promote sustainability of the palm oil industry.  It is envisaged that POME can be sustainably reused as a fermentation substrate in production of various metabolites through biotechnological advances. In addition, POME consists of high organic acids and is suitable to be used as a carbon source.

POME has emerged as an alternative option as a chemical remediation to grow microalgae for biomass production and simultaneously act as part of wastewater treatment process. POME contains hemicelluloses and lignocelluloses material (complex carbohydrate polymers) which result in high COD value (15,000–100,000 mg/L).

POME-Biogas

Utilizing POME as nutrients source to culture microalgae is not a new scenario, especially in Malaysia. Most palm oil millers favor the culture of microalgae as a tertiary treatment before POME is discharged due to practically low cost and high efficiency. Therefore, most of the nutrients such as nitrate and ortho-phosphate that are not removed during anaerobic digestion will be further treated in a microalgae pond. Consequently, the cultured microalgae will be used as a diet supplement for live feed culture.

In recent years, POME is also gaining prominence as a feedstock for biodiesel production, especially in the European Union. The use of POME as a feedstock in biodiesel plants requires that the plant has an esterification unit in the back-end to prepare the feedstock and to breakdown the FFA. In recent years, biomethane production from POME is also getting traction in Indonesia and Malaysia.

Why Does Waste Matter in the Gaia Theory?

  By | | , , ,
2 Comments

Do you know where your food comes from and where the uneaten leftovers go after you’ve thrown them away?

Whether you’re thinking about it or not, every action you take has some effect on the world around you. A chemist named James Lovelock hypothesized that living organisms interact with their surroundings to maintain a livable environment.

Today, this is known as the Gaia Theory.

Why Waste Matter in the Gaia Theory

The Gaia Theory

One of the defining points of the gaia theory is that organisms live synergistically with the Earth. All plants, animals, and people contribute to a stable environment simply by living in it.

Unfortunately, wasteful habits by people do the opposite. Actions that harm entire populations of organisms will have a waterfall effect that harms the environment. An example of this is found in trees.

Wood is a necessary product in day-to-day life. However, harvesting too much wood without a replacement plan or not fully utilizing the wood harvested decimates the tree populations. Trees pull carbon, the most common greenhouse gas, from the air and replace it with oxygen. If the number of trees decreases, the mass of carbon increases, which encourages the onset of global warming.

Global warming then weakens populations of other organisms, which in turn further worsens the environment. Every living thing depends on one another.

Global Warming

The Earth is no stranger to mass extinction events. Throughout history, incredible incidents such as meteors, continent-wide wildfires, and volcanoes have directly caused global warming and cooling. Surviving plants, animals, fungi, and microorganisms all contributed to the Earth’s recovery from such events.

Scientists are currently theorizing that we are in the middle of yet another mass extinction event, due to pollution, overdevelopment, and waste. During the worst-case scenario, the Earth will recover from this, but only after millions of years.

The more biodiversity is lost, the longer the environment will take to recover. More must be done to protect and preserve what is left to keep the Earth habitable for as long as possible.

Waste Not, Want Not

National Geographic outlines the harmful effects of plastic waste that hasn’t been properly disposed of or recycled. This plastic primarily ends up in the oceans, which impedes life even at the microscopic level.

Plastic takes centuries to decompose but will still break down into “microplastics” that have infected every water system in the world. This is not only toxic for animals, but people as well. Every creature can be harmed by the ingestion of plastic, contributing to mass extinctions, and further jeopardizing the livability of the Earth.

plastic waste

The main culprit is single-use plastic, which accounts for 40 percent of the plastics produced yearly. This includes plastic grocery bags and packaging.

Plastic production and use are increasing exponentially, with no real change in how plastics are disposed of. To protect our environment, this must change.

The Best Time to Start is Now

Waste may be an unavoidable part of life, but it can still be managed. The worse global warming gets, the more resources will be needed to combat it, and the more impact waste has on all of us. The complex system that is the Earth can only self-regulate if we allow it to.

You can do your part today to minimize your own waste. Taking the advice of professionals and being mindful of how you interact with the environment you live in are important steps.

Remember, we all live on this Earth together, and must do our best to take care of it.

5 Money-Saving Upgrades To Make Your Home Energy-Efficient

  By | | , ,
5 Comments

Did you know the average American household spends about $2,000 annually for utilities? What’s more, $200 to $400 is money wasted due to drafts, air leakage, and outdated HVAC systems. That’s a lot of money, right? You can save that money by making energy efficient upgrades to your home.

Let’s take a look at these money-saving upgrades, shall we?

1. Insulation

A very cost effective way to save on energy is by adding more insulation in the attic, or switching out the typical blanket insulation for either cellulose loose-fill insulation or spray foam insulation. The spray foam insulation is the most effective type of insulation for energy efficiency.

home-insulation

With that in mind, installing spray foam insulation requires professional installation and it can range anywhere from $1 to $1.50 per square foot.

2. Energy efficient appliances and HVAC system

Older appliances tend to use a of energy and are nowhere near as energy efficient as newer models. Look for appliances and electronics that are ENERGY STAR approved products. By replacing the refrigerator, washer and dryer and even the ranges, you can save 15% on how much energy your home uses.

The same with heating and cooling. When you upgrade your HVAC system, you can save up to 20% to 50% on your energy bills – providing you make some of the other upgrades on this list.

hvac-repair

3. Programmable thermostat

It seems like everything is a smart device doesn’t it? Smart thermostats are an excellent way to reduce the amount of heating and cooling is used, especially when you’re not home. In the winter, you can decrease the temperature when you’re not at home and increase it to a comfortable temperature about 30 minutes before you get home, and vice versa.

eco-friendly-business-practices

If you don’t want to go the smart thermostat route, there are programmable thermostats where you can change the settings so the temperature is where it’s set to at the desired time.

4. Eliminating air leaks

One of the biggest culprits of wasted energy is air leakages. A whopping 40% of a home’s heating or cooling is lost due to drafty doors and windows and ill-fitted air ducts. You can prevent this by upgrading your doors and windows to high energy options. Not only are the new doors and windows themselves energy efficient, but the new seals will prevent air leakage. Save your precious time by using an estimating software to find out the cost incurred in home upgrades.

If you cannot afford new windows or doors, you can always use exterior-grade caulking and new weatherstripping to seal up cracks or gaps you may find.

5. Install ceiling fans

Ceiling fans are a great way to add a bit of style to a room, but they can also help circulate the air, regardless of the season. Most fans have a switch that allows you to change the direction the fan moves. In the summer, it should rotate counterclockwise to push the cooler air down, therefore making the air feel cooler than it actually is. In the winter, it should rotate clockwise to pull the cool air upward and push the warm air downward.

Keeping your home’s energy costs as low as possible isn’t just smart as a homeowner, it’s also a good way to increase the value of your home. And, according to HomeLight’s Q2 2020 survey, we are in a seller’s market! 60% of agents who participated in the survey said there were 60% more bidding wars in June 2020 and the market doesn’t seem to be slowing.

That means if you’re looking to sell, these energy efficient upgrades are a great way to pique a buyer’s interest – maybe even more than one!

Biofuels from Syngas

  By | | , ,
12 Comments

An attractive approach to converting biomass into liquid or gaseous fuels is direct gasification, followed by conversion of the syngas to final fuel. Ethanol can be produced this way, but other fuels can be produced more easily and potentially at lower cost, though none of the approaches is currently inexpensive.

The choice of which process to use is influenced by the fact that lignin cannot easily be converted into a gas through biochemical conversion. Lignin can, however, be gasified through a heat process. The lignin components of plants can range from near 0% to 35%. For those plants at the lower end of this range, the chemical conversion approach is better suited. For plants that have more lignin, the heat-dominated approach is more effective.

Gasification_Process

Layout of a Typical Biomass Gasification Plant

Once the gasification of biomass is complete, the resulting syngas or synthetic gas can be used in a variety of ways to produce liquid fuels as mentioned below

Fischer-Tropsch (F-T) fuels

The Fischer-Tropsch process converts “syngas” (mainly carbon monoxide and hydrogen) into diesel fuel and naphtha (basic gasoline) by building polymer chains out of these basic building blocks. Typically a variety of co-products (various chemicals) are also produced.

The Fisher-Tropsch process is an established technology and has been proven on a large scale but adoption has been limited by high capital and O&M costs. According to Choren Industries, a German based developer of the technology, it takes 5 tons of biomass to produce 1 ton of biodiesel, and 1 hectare generates 4 tons of biodiesel.

Methanol

Syngas can also be converted into methanol through dehydration or other techniques, and in fact methanol is an intermediate product of the F-T process (and is therefore cheaper to produce than F-T gasoline and diesel).

Methanol is somewhat out of favour as a transportation fuel due to its relatively low energy content and high toxicity, but might be a preferred fuel if fuel cell vehicles are developed with on-board reforming of hydrogen.

Dimethyl ether

DME also can be produced from syngas, in a manner similar to methanol. It is a promising fuel for diesel engines, due to its good combustion and emissions properties. However, like LPG, it requires special fuel handling and storage equipment and some modifications of diesel engines, and is still at an experimental phase.

If diesel vehicles were designed and produced to run on DME, they would become inherently very low pollutant emitting vehicles; with DME produced from biomass, they would also become very low GHG vehicles.

The UK’s E-Waste Problem

  By | | , ,
2 Comments

There’s no doubt that the UK is in the midst of an electronic waste crisis with more than two thirds of households sitting on old phone chargers, along with other items. A study by OKdo shows exactly how big our e-waste problem is, why it’s an issue and how we can dispose of electronic items safely and responsibly.

Here we’ll take a look at the key findings and help you get clued up on what to do with your old electronic items without adding to the UK’s landfill.

e-waste crisis in united kingdom

The UK produces some of the biggest e-waste

With an average of 23.9kg of e-waste per person, the UK is one of the top e-waste producers in the world. Shockingly, during the first six months of 2021, the country produced an amount of electronic waste equivalent to 15 Eiffel Towers.

Cables seem to be a huge contributing factor with 140 million being stored in homes up and down the country. Not only this, households have up to 60 items of old electronics that are left unused in drawers and cupboards.

Why is there such a big e-waste problem?

The main issue appears to be that people simply don’t know how to recycle their old technology with 38% of people aged 45-54 having never done it and are unsure how to. The younger Millennials are more clued up with 31% knowing how to recycle their e-waste.

With electronic products increasing every year and the demand for more digital technology due to remote working, the problem of electronic waste is only going to get worse. Add to this our culture’s obsession with having the latest gadgets and brand-new phones and smart devices, and it’s not difficult to see we’re heading for a serious landfill and environmental issue.

How can we dispose of e-waste safely?

Donating to charity is one way to dispose of unused tech without clogging up landfill. Charities will often donate such technology to communities where items are needed so you’ll be helping others too.

electrical-waste-uk

There are also many company initiatives and services which encourage the recycling of old items, often rewarding you for doing so in the form of vouchers or money off a new tech device.

Council collections or recycling centres are another option if you’re looking for a local site to take your old items to. It’s worth checking your local council to make sure your device can be recycled.

By raising awareness of the e-waste problem and making sure we know how to recycle our old technology, we can contribute to a safer and greener environment and possibly help other communities along the way.